某园区组网方案如图1-1所示，数据规划如表1-1内容所示。
[问题1] 以Switch3为例配置接入层交换机，补充下列命令片段。< HUAWEI> (1)[HUAWEI] sysname Switch3 [Switch3] vlan batch (2)[Switch3] interface GigabitEthernet 0/0/3 [Switch3-GigabitEthernet0/0/3] port link-type (3) [Switch3-
GigabitEthernet0/0/3] port trunk allow-pass vlan 10 20 [Switch3-GigabitEthernet0/0/3] quit [Switch3] interface GigabitEthernet 0/0/1 [Switch3-GigabiEthernet0/0/1] port link-type (4) [Switch3-GigabitEthernet0/0/1] port default vlan 10[Switch3-
GigabitEthernet/0/1] quit[Switch3] stp bpdu-protection [问题2] 以Switch1为例配置核心层交换机，创建其与接入交换机、备份设备以及出口路由器的互通VLAN，补充下列命令。< HUAWEI> system-view[HUAWEI] sysname Switch1 [Switch1] vlan batch (5) [Switch1] interface GigabitEthernet/0/1 [SwitchI-GigabitEthernet0/0/1] port link-type trunk [Switchl-GigabitEthernet0/0/1] port trunk allow-pass (6)[Switch1-GigabitEthernet0/0/1] quit[Switch1] interface Vlanif 10 [Switch1-Vlanif10] ip address 192.168.10.1 24 [Switch1-Vlanif10] quit[Switch1] interface Vlanif 20[Switch1-Vlanif20] ip address 192.1 68.20.1 24[Switch1-Vlanif20] quit[Switch1] interface GigabitEthernet 0/0/7[Switchl-GigabitEthernet0/0/7] port link-type trunk[Switch1-GigabitEthernet0/0/7] port trunk allow-pass vlan 100[Switch1-GigabitEthernet0/0/7] quit[Switch1] interface Vlanif 100[Switch1-Vlanif100] ip address (7)[Switch1-Vlanif100] quit[Switch1] interface GigabitEthernet 0/0/5[Switch1-GigabitEthernet0/0/5] port link-type access[Switch1-GigabitEthernet0/0/5] port default vlan 300[Switchl-GigabitEthernet0/0/5] quit[Switch1 interface Vlanif 300[SwitchI-Vlanif300] ip address (8)[Switchl-Vlanif300] quit [问题3] 如果配置静态路由实现网络互通，补充在Switch1和Router上配置的命令片段。[Switch1] ip route-static (9) /默认优先级[Switch1] ip route-static 0.0.0.0 0.0.0.0 172.16.30.2 preference 70[Router] ip route-static (10) /默认优先级[Router] ip route-static 192. 168.10.0 255.255.255.0 172.16.10.1 [Router] ip route-static 192.168. 10.0 255.255.255.0 172.16.20.1 preference70[Router] ip route-static 192.1 68.20.0 255.255.255.0 172.16.10.1[Router] ip route-static 192.1 68.20.0 255.255.255.0 172.16.20.1 preference70
正确答案及解析
正确答案
解析
[问题1] 命令填空，一定要充分利用上下文之间的关系。[问题2] 还是根据上下文和表格中的地址参数，直接填写即可。[问题3] 还是根据上下文和表格中的地址参数，直接填写即可。
答案: [问题1](1) system-view (2) 1020 (3) trunk (4) access
[问题2] (5) 1020100300 (6) vlan1020 (7) 172.16.10.124或者172.16.10.1255.255.255.0 (8) 172.16.30.124或者172.16.30.1255.255.255.0
[问题3](9) 0.0.0.00.0.0.0172.16.10.2 (10) 0.0.0.00.0.0.0202.101.111.1
